PL EN
 
PL EN
Current issue
About the Journal
Editorial Board
Editorial Office and Publisher
Article Processing Charge
Open Access
Topic Manufacturing and Technology
 

Cutting Forces and 3D Surface Analysis of CFRP Milling
Katarzyna Biruk-Urban, Jerzy Józwik, Paul Bere
Adv. Sci. Technol. Res. J. 2022; 16(2):206–215
DOI: https://doi.org/10.12913/22998624/147338
 

Study of Cross Wedge Rolling Process of BA3002-Type Railway Axle
Zbigniew Pater
Adv. Sci. Technol. Res. J. 2022; 16(2):225–231
DOI: https://doi.org/10.12913/22998624/147310
 

Parametric Analysis on the Progression of Mechanical Properties on FSW of Aluminum-Copper Plates
Anil Kumar Deepati, Waleed Alhazmi, Waleed Zakri, Essam Shaban, Pankaj Biswas
Adv. Sci. Technol. Res. J. 2022; 16(2):168–178
DOI: https://doi.org/10.12913/22998624/147123
 

Investigation of the Surface Topography of Titanium Alloys Applied to Friction Components
Grzegorz Gawłowski, Magdalena Niemczewska-Wójcik
Adv. Sci. Technol. Res. J. 2022; 16(2):150–158
DOI: https://doi.org/10.12913/22998624/147070
 

Experimental Analysis of the Post-Buckling Behaviour of Compressed Stiffened Panel with Refill Friction Stir Spot Welded and Riveted Stringers
Andrzej Kubit, Łukasz Święch, Tomasz Trzepieciński, Koen Faes
Adv. Sci. Technol. Res. J. 2022; 16(2):159–167
DOI: https://doi.org/10.12913/22998624/146899
 

Chip Temperature Measurement in the Cutting Area During Rough Milling Magnesium Alloys with a Kordell Geometry End Mill
Józef Kuczmaszewski, Ireneusz Zagórski, Piotr Zgórniak
Adv. Sci. Technol. Res. J. 2022; 16(2):109–119
DOI: https://doi.org/10.12913/22998624/146851
 

2D Geometric Surface Structure ANN Modeling after Milling of the AZ91D Magnesium Alloy
Monika Kulisz, Ireneusz Zagórski, Jerzy Józwik
Adv. Sci. Technol. Res. J. 2022; 16(2):131–140
DOI: https://doi.org/10.12913/22998624/146765
 

Study on the Machinability of Glass, Carbon and Aramid Fiber Reinforced Plastics in Drilling and Secondary Drilling Operations
Krzysztof Ciecieląg
Adv. Sci. Technol. Res. J. 2022; 16(2):57–66
DOI: https://doi.org/10.12913/22998624/146079
 

Intelligent Visual Quality Control System Based on Convolutional Neural Networks for Holonic Shop Floor Control of Industry 4.0 Manufacturing Systems
Przemysław Oborski, Przemysław Wysocki
Adv. Sci. Technol. Res. J. 2022; 16(2):89–98
DOI: https://doi.org/10.12913/22998624/145503
 

Testing the Use of Rounded Valley Aggregate in Concrete Mix in Comparison with Crushed Limestone Aggregate
Mohmd Kh Sarireh
Adv. Sci. Technol. Res. J. 2022; 16(1):282–293
DOI: https://doi.org/10.12913/22998624/145497
 

Correlation Studies of Dimensional Accuracy with Temperature Changes of Selected Elements of a Machine Tool in the Machining Process
Damian Basara, Leszek Skoczylas
Adv. Sci. Technol. Res. J. 2022; 16(1):253–259
DOI: https://doi.org/10.12913/22998624/145424
 

Influence of Selected Diagnostic Parameters on the Quality of AWJ Cutting Surface
Tomasz Wala, Krzysztof Lis
Adv. Sci. Technol. Res. J. 2022; 16(1):129–140
DOI: https://doi.org/10.12913/22998624/144642
 

Accuracy of the New Method of Alignment of Workpiece Using Structural-Light 3D Scanner
Andrzej Gessner, Wojciech Ptaszyński, Waldemar Adam
Adv. Sci. Technol. Res. J. 2022; 16(1):1–14
DOI: https://doi.org/10.12913/22998624/144541
 

Technological Possibilities of the Carbide Tools Application for Precision Machining of WCLV Hardened Steel
Marcin Grabowski, Józef Gawlik, Joanna Krajewska-Śpiewak, Sebastian Skoczypiec, Piotr Tyczyński
Adv. Sci. Technol. Res. J. 2022; 16(1):141–148
DOI: https://doi.org/10.12913/22998624/144340
 

Investigations of Adhesive Properties of Polyamide Modified with Friction Reducing Agents
Kamil Anasiewicz, Józef Kuczmaszewski
Adv. Sci. Technol. Res. J. 2022; 16(1):113–121
DOI: https://doi.org/10.12913/22998624/144337
 

Automated Production Line Reliability Analysis of the Crankshaft Manufacturing Process
Abass Enzi, Sardar Asif
Adv. Sci. Technol. Res. J. 2022; 16(1):15–27
DOI: https://doi.org/10.12913/22998624/143936
 

Study on Chip Breakability Index During Longitudinal Turning of Cast and DMLS Additively Manufactured AlSi10Mg Aluminum Alloy
Grzegorz Krzysztof Struzikiewicz, Bogdan Słodki, Wojciech Zębala, Emilia Franczyk
Adv. Sci. Technol. Res. J. 2022; 16(1):28–35
DOI: https://doi.org/10.12913/22998624/143503
 

The Analysis of the Influence of Technological Parameters on the Grinding Temperature in the Single-Pass Grinding Process of Solid Carbide End Mill Flutes
Marcin Sałata
Adv. Sci. Technol. Res. J. 2022; 16(1):190–202
DOI: https://doi.org/10.12913/22998624/143483
 

Analysis of the Impact of Wiper Geometry Insert on Surface Roughness and Chips in Machining Materials Used in the Aviation Industry
Piotr Szablewski, Krzysztof Smak, Bartłomiej Krawczyk
Adv. Sci. Technol. Res. J. 2022; 16(1):203–212
DOI: https://doi.org/10.12913/22998624/143475
 

Effect of Surface Abrasive Treatment on the Strength of Galvanised Steel Sheet Adhesive Joints
Izabela Miturska-Barańska, Anna Rudawska
Adv. Sci. Technol. Res. J. 2022; 16(1):75–84
DOI: https://doi.org/10.12913/22998624/143471
 

Influence of Minimum Quantity Lubrication Using Vegetable-Based Cutting Fluids on Surface Topography and Cutting Forces in Finish Turning of Ti-6Al-4V
Joanna Lisowicz, Witold Habrat, Krzysztof Krupa
Adv. Sci. Technol. Res. J. 2022; 16(1):95–103
DOI: https://doi.org/10.12913/22998624/143289
 

Path Interval and Its Relevance to Cutting Force in Ball and Filleted End Milling
Tsutomu Sekine
Adv. Sci. Technol. Res. J. 2022; 16(1):85–94
DOI: https://doi.org/10.12913/22998624/143051
 

Surface Topography of Inconel 718 Alloy in Finishing WEDM
Jarosław Buk
Adv. Sci. Technol. Res. J. 2022; 16(1):47–61
DOI: https://doi.org/10.12913/22998624/142962
 

Research of the Tool Velocity and Product Shape Aspects of the Hot Radial Rolling of C45 Steel Rings
Piotr Surdacki, Andrzej Gontarz, Grzegorz Winiarski, Grzegorz Samołyk
Adv. Sci. Technol. Res. J. 2021; 15(4):352–363
DOI: https://doi.org/10.12913/22998624/143269
 

Influence of Grain Size and Feed Rate on Selected Aspects of Corundum Ceramic Grinding Using Spherical Diamond Heads
Artur Szajna, Anna Bazan
Adv. Sci. Technol. Res. J. 2021; 15(4):149–159
DOI: https://doi.org/10.12913/22998624/142629
 

The Manufacturing of Composite Materials in the Matrix of Modified Phenol-Formaldehyde Resins
Volodymyr Krasinskyi, Tomasz Jachowicz, Ludmila Dulebova, Ivan Gajdoš, Rafał Malinowski
Adv. Sci. Technol. Res. J. 2021; 15(4):267–272
DOI: https://doi.org/10.12913/22998624/142288
 

Assessment of the Possibility of Using Fractal Analysis to Describe the Surface Aluminum Composites After Turning
Paweł Karolczak, Maciej Kowalski, Katarzyna Raszka
Adv. Sci. Technol. Res. J. 2021; 15(4):49–60
DOI: https://doi.org/10.12913/22998624/141935
 

Digital Shape and Geometric Dimension Analysis of Polymer Fuel Tanks
Jerzy Józwik, Krzysztof Dziedzic
Adv. Sci. Technol. Res. J. 2021; 15(4):38–48
DOI: https://doi.org/10.12913/22998624/141649
 

Comparative Study on Path Interval and Two Tool Condition Parameters in Ball and Filleted End Milling
Tsutomu Sekine
Adv. Sci. Technol. Res. J. 2021; 15(4):311–320
DOI: https://doi.org/10.12913/22998624/141258
 

Using Agglomeration Techniques for Coal and Ash Waste Management in the Circular Economy
Gabriel Borowski, Sameh Alsaqoor, Ali Alahmer
Adv. Sci. Technol. Res. J. 2021; 15(3):264–276
DOI: https://doi.org/10.12913/22998624/140784
 

Effect of Ceramic Brush Treatment on the Surface Quality and Edge Condition of Aluminium Alloy after Abrasive Waterjet Machining
Jakub Matuszak
Adv. Sci. Technol. Res. J. 2021; 15(3):254–263
DOI: https://doi.org/10.12913/22998624/140336
 

Bead-on-Plate Underwater Wet Welding on S700MC Steel
Jacek Tomków, Aleksandra Świerczyńska, Michał Landowski, Adrian Wolski, Grzegorz Rogalski
Adv. Sci. Technol. Res. J. 2021; 15(3):288–296
DOI: https://doi.org/10.12913/22998624/140223
 

Modeling of Vibration Behaviors of Turning Machining with the Constant Surface Speed Effect
Muhamad Aditya Royandi, Iman Apriana Effendi, Bustami Ibrahim, Jui Pin Hung
Adv. Sci. Technol. Res. J. 2021; 15(3):134–145
DOI: https://doi.org/10.12913/22998624/138925
 

Fire Detection Methods Based on Various Color Spaces and Gaussian Mixture Models
Amr Munshi
Adv. Sci. Technol. Res. J. 2021; 15(3):197–214
DOI: https://doi.org/10.12913/22998624/138924
 

Study on Tool Condition Parameters Intended for Smart Tool Management in Filleted End Milling
Tsutomu Sekine
Adv. Sci. Technol. Res. J. 2021; 15(3):108–116
DOI: https://doi.org/10.12913/22998624/138532
 

Advances in Surface Engineering Using TIG Processing to Incorporate Ceramic Particulates into Low Alloy and Microalloyed Steels – A Review
Patricia Munoz-Escalona, Shahjahan Mridha, Thomas Neville Baker
Adv. Sci. Technol. Res. J. 2021; 15(3):88–98
DOI: https://doi.org/10.12913/22998624/138467
 

Intelligent Machining of Shape Memory Alloys
Kapil Gupta
Adv. Sci. Technol. Res. J. 2021; 15(3):43–53
DOI: https://doi.org/10.12913/22998624/138303
 

Influence of Hole Chamfer Size on Strength of Blind Riveted Joints
Monika Lubas, Lucjan Witek
Adv. Sci. Technol. Res. J. 2021; 15(2):49–56
DOI: https://doi.org/10.12913/22998624/135632
 

The Optimization of PHBV-hemp Fiber Biocomposite Manufacturing Process on the Selected Example
Wiesław Jan Frącz, Grzegorz Janowski, Łukasz Bąk
Adv. Sci. Technol. Res. J. 2021; 15(2):127–137
DOI: https://doi.org/10.12913/22998624/135399
 

Simulation of Superfinished Surface Formation
Augustín Görög
Adv. Sci. Technol. Res. J. 2021; 15(2):219–227
DOI: https://doi.org/10.12913/22998624/133064
 

Proposal of a Method for Measuring Gas Flow in a Heating Furnace: A Simulation Study
Marcel Pástor, Milan Durdán, Ján Kačur, Marek Laciak, Patrik Flegner
Adv. Sci. Technol. Res. J. 2021; 15(2):1–12
DOI: https://doi.org/10.12913/22998624/132952
 

Structural Analysis and Optimization of Electric Bike Front Drive with Bottom Bracket Electric Motor
Elmedin Mesic, Adnan Masic, Enis Muratović, Muamer Delic, Salem Hasanbegovic
Adv. Sci. Technol. Res. J. 2021; 15(1):273–282
DOI: https://doi.org/10.12913/22998624/132613
 

Use of 3D Parametric Models in the Automotive Component Design Process
Michal Fabian, František Kupec
Adv. Sci. Technol. Res. J. 2021; 15(1):255–264
DOI: https://doi.org/10.12913/22998624/132589
 

Increasing Competitiveness Through Innovation in an Industrial Enterprise – A Case Study of the Company Massag
Filip Šproch, Jan Nevima
Adv. Sci. Technol. Res. J. 2021; 15(1):110–125
DOI: https://doi.org/10.12913/22998624/130862
 

Influence of Centrifugal Shot Peening Parameters on the Impact Force and Surface Roughness of EN-AW 2024 Aluminum Alloy Elements
Agnieszka Skoczylas
Adv. Sci. Technol. Res. J. 2021; 15(1):71–78
DOI: https://doi.org/10.12913/22998624/130511
 

Differences in Roughness Parameter Values from Skid and Skidless Contact Stylus Profilometers
Karol Grochalski, Michał Mendak, Michał Jakubowicz, Bartosz Gapiński, Natalia Swojak, Michał Wieczorowski, Aleksandra Krawczyk
Adv. Sci. Technol. Res. J. 2021; 15(1):58–70
DOI: https://doi.org/10.12913/22998624/130453
 

Influence of the Biocidal Agent Layer on Selected Properties of the Blown Polyethylene Film
Łukasz Majewski, Mariusz Kłonica, Tomasz Jachowicz
Adv. Sci. Technol. Res. J. 2020; 14(4):315–325
DOI: https://doi.org/10.12913/22998624/128848
 

Mechanical Properties and Sliding Wear Resistance of Suspension Plasma Sprayed YSZ Coatings
Leszek Łatka, Mirosław Szala, Wojciech Macek, Ricardo Branco
Adv. Sci. Technol. Res. J. 2020; 14(4):307–314
DOI: https://doi.org/10.12913/22998624/128574
 

Heuristic Adaptive Control of Waste Gas Exhausting in Coke Making
Ján Kačur, Patrik Flegner, Milan Durdán, Marek Laciak
Adv. Sci. Technol. Res. J. 2020; 14(4):195–212
DOI: https://doi.org/10.12913/22998624/128395
 

Modern Reverse Engineering Methods Used to Modification of Jewelry
Arkadiusz Kroma, Oliwia Adamczak, Robert Sika, Filip Górski, Wiesław Kuczko, Krzysztof Grześkowiak
Adv. Sci. Technol. Res. J. 2020; 14(4):298–306
DOI: https://doi.org/10.12913/22998624/128006
 

Statistical Comparison of the Hardness and Scratch-Resistance of the PMMA Polymers Used in Orthodontic Appliances
Ivo Domagała, Leszek Gil, Marcel Firlej, Daniel Pieniak, Jarosław Selech, Dawid Romek, Barbara Biedziak
Adv. Sci. Technol. Res. J. 2020; 14(4):250–261
DOI: https://doi.org/10.12913/22998624/127437
 

Influence of the Length of Components From Polymer Composite on Selected Machinability Indicators in the Circumferential Milling Process
Krzysztof Ciecieląg
Adv. Sci. Technol. Res. J. 2020; 14(4):229–239
DOI: https://doi.org/10.12913/22998624/127010
 

The Study on the Damage of the Rear-Axle Shaft in a KIA Truck
Krzysztof Siczek, Marek Wozniak, Gustavo Ozuna
Adv. Sci. Technol. Res. J. 2020; 14(4):115–124
DOI: https://doi.org/10.12913/22998624/126508
 

Methodological Procedures Applied to the Manufacturing Systems Design
Naqib Daneshjo
Adv. Sci. Technol. Res. J. 2020; 14(4):86–95
DOI: https://doi.org/10.12913/22998624/125579
 

Temperature Measurement of Modern Cutting Tools During Turning
Karol Grochalski, Piotr Jabłoński, Rafał Talar, Paweł Twardowski, Michał Wieczorowski, Bartosz Jakubek, Wojciech Rukat
Adv. Sci. Technol. Res. J. 2020; 14(4):37–48
DOI: https://doi.org/10.12913/22998624/123007
 

Selection of the Technological Ceramic Layer Thickness in an HPDC Machine Plunger in the Aspect of its Strength
Jacek Jankowski, Dariusz Kołakowski, Bogusław Pisarek
Adv. Sci. Technol. Res. J. 2020; 14(4):11–20
DOI: https://doi.org/10.12913/22998624/118399
 

Thin and Rectangular Die Bond Pick-Up Mechanism to Reduce Cracking During the Integrated Circuit Assembly Process
Ahmad R.A. Rahman, Nazrul Anuar Nayan
Adv. Sci. Technol. Res. J. 2020; 14(3):57–64
DOI: https://doi.org/10.12913/22998624/123779
 

Quality of Samples in Adhesive Joint Testing
Magdalena Zawada-Michałowska, Józef Kuczmaszewski
Adv. Sci. Technol. Res. J. 2020; 14(3):182–191
DOI: https://doi.org/10.12913/22998624/123112
 

Thermal Oxidation Stability of Lubricating Greases
Wojciech Krasodomski, Agnieszka Skibińska, Magdalena Żółty
Adv. Sci. Technol. Res. J. 2020; 14(3):75–82
DOI: https://doi.org/10.12913/22998624/122569
 

Nanocomposites Based on Polyamide and Montmorillonite Obtained from a Solution
Volodymyr Krasinskyi, Oleh Suberlyak, Viktoria Kochubei, Tomasz Jachowicz, Ludmila Dulebova, Viktoria Zemke
Adv. Sci. Technol. Res. J. 2020; 14(3):192–198
DOI: https://doi.org/10.12913/22998624/122297
 

Technological and Economic Analysis of Logistic Activities in Interior Parts Manufacturing
Libor Kavka, Iveta Dočkalíková, Zdeněk Čujan, Gabriel Fedorko
Adv. Sci. Technol. Res. J. 2020; 14(3):204–212
DOI: https://doi.org/10.12913/22998624/122062
 

Prediction of Surface Roughness Based on the Machining Conditions with the Effect of Machining Stability
Yung-Chih Lin, You-Chen Chen, Kung-Da Wu, Jui-Pin Hung
Adv. Sci. Technol. Res. J. 2020; 14(2):171–183
DOI: https://doi.org/10.12913/22998624/119048
 

A Computational Algorithm for Path Interval Determination in Multi-Axis Filleted End Milling
Tsutomu Sekine
Adv. Sci. Technol. Res. J. 2020; 14(2):198–205
DOI: https://doi.org/10.12913/22998624/119047
 

Impact of Assembly Method on the Strength of Single-Lap Joints of Aircraft Aluminum Alloy Sheets
Izabela Miturska
Adv. Sci. Technol. Res. J. 2020; 14(2):163–170
DOI: https://doi.org/10.12913/22998624/119046
 

Machining of Composite Materials by Ultrasonic Assistance
Marcel Kuruc
Adv. Sci. Technol. Res. J. 2020; 14(2):140–144
DOI: https://doi.org/10.12913/22998624/118943
 

Solving the Spatial Relationships in Manufacturing Systems
Naqib Daneshjo, Albert Mareš, Erika Dudáš Pajerská
Adv. Sci. Technol. Res. J. 2020; 14(2):120–130
DOI: https://doi.org/10.12913/22998624/118941
 

Application of X-ray Diffraction for Residual Stress Analysis in Truncated Cones Made by Incremental Forming
Bogdan Krasowski, Andrzej Kubit, Tomasz Trzepieciński, Kazimiera Dudek, Jan Slota
Adv. Sci. Technol. Res. J. 2020; 14(2):103–111
DOI: https://doi.org/10.12913/22998624/118829
 

Effect of Test Velocity on the Energy Absorption Under Progressive Crushing of Composite Tubes
Grażyna Ryzińska, Roman Gieleta
Adv. Sci. Technol. Res. J. 2020; 14(2):94–102
DOI: https://doi.org/10.12913/22998624/118551
 

Study of the Performance of Natural Fiber Reinforced Composites for Wind Turbine Blade Applications
Temesgen Batu, Hirpa G. Lemu, Belete Sirhabizuh
Adv. Sci. Technol. Res. J. 2020; 14(2):67–75
DOI: https://doi.org/10.12913/22998624/118201
 

Mechanical and Thermal Stresses in an HPDC Machine Plunger During the Dosing and Filling Process
Jacek Jankowski, Dariusz Kołakowski, Boguslaw Pisarek
Adv. Sci. Technol. Res. J. 2020; 14(2):1–12
DOI: https://doi.org/10.12913/22998624/118187
 

Mathematical Modeling of Material Erosion During the Electrical Discharge
Zbigniew Gulbinowicz, Olgierd Janusz Goroch, Paweł Skoczylas
Adv. Sci. Technol. Res. J. 2020; 14(2):27–33
DOI: https://doi.org/10.12913/22998624/114959
 

Potential and Limits of Overall Equipment Effectiveness in the Total Productivity Management
Ivana Šajdlerová, Vladimíra Schindlerová, Jiří Kratochvíl
Adv. Sci. Technol. Res. J. 2020; 14(2):19–26
DOI: https://doi.org/10.12913/22998624/113617
 

Analysis of Mechanical and Thermal Stresses in a Pressure Casting Machine Plunger
Jacek Jankowski, Dariusz Kołakowski, Bogusław Pisarek
Adv. Sci. Technol. Res. J. 2020; 14(1):209–223
DOI: https://doi.org/10.12913/22998624/117724
 

The Influence of Technological Factors on the Strength of Adhesive Joints of Steel Sheets
Elżbieta Doluk, Anna Rudawska, Valentina Brunella
Adv. Sci. Technol. Res. J. 2020; 14(1):107–115
DOI: https://doi.org/10.12913/22998624/116549
 

Highly Efficient Milling on the Example of Selected Machining Strategies
Kazimierz Zaleski, Jakub Matuszak, Andrzej Zyśko
Adv. Sci. Technol. Res. J. 2020; 14(1):167–177
DOI: https://doi.org/10.12913/22998624/116356
 

Development of Ammunition with Unconventional Applications
Olgierd Janusz Goroch, Gulbinowicz Zbigniew, Cybula Leszek
Adv. Sci. Technol. Res. J. 2020; 14(1):137–144
DOI: https://doi.org/10.12913/22998624/115515
 

Numerical Analysis of the Cross-Wedge of a Hollow Rail Axle
Zbigniew Pater, Konrad Lis, Patrycja Walczuk-Gągała
Adv. Sci. Technol. Res. J. 2020; 14(1):145–153
DOI: https://doi.org/10.12913/22998624/115513
 

Numerical Modeling of Superplastic Punchless Deep Drawing Process of a Ti-6Al-4V Titanium Alloy
Marta Wójcik, Andrzej Skrzat
Adv. Sci. Technol. Res. J. 2020; 14(1):127–136
DOI: https://doi.org/10.12913/22998624/114029
 

Use of the Dynamic Simulation to Reduce Handling Complexity in the Manufacturing Process
Vladimíra Schindlerová, Ivana Šajdlerová
Adv. Sci. Technol. Res. J. 2020; 14(1):81–88
DOI: https://doi.org/10.12913/22998624/113616
 

The Effect of Artificial Ageing on the Mechanical Properties of the EN AW 2017 Alloy
Klara Jirounkova, Jan Vozka, Jaromir Cais
Adv. Sci. Technol. Res. J. 2020; 14(1):75–80
DOI: https://doi.org/10.12913/22998624/113614
 

The Strength of the Adhesive Joints of the Medium-Density Fireboards and Particle Boards with the PVC Film
Anna Rudawska, Dana Stančeková, Mirosław Müller, Tatiana Vitenko, Vlodymyr Iasnii
Adv. Sci. Technol. Res. J. 2020; 14(1):58–68
DOI: https://doi.org/10.12913/22998624/113612
 

Strength of Assembly Butt Joints of Plastic Pipes
Izabela Miturska, Anna Rudawska, Valentina Brunella
Adv. Sci. Technol. Res. J. 2020; 14(1):10–17
DOI: https://doi.org/10.12913/22998624/113544
 

Rapid Manufacturing of Individualized Prosthetic Sockets
Filip Górski, Radosław Wichniarek, Wiesław Kuczko, Magdalena Żukowska, Ewa Suszek
Adv. Sci. Technol. Res. J. 2020; 14(1):42–49
DOI: https://doi.org/10.12913/22998624/113425
 

Analysis of the Possibilities of Improving the Selected Properties Surface Layer of Butt Joints Made Using the FSW Method
Magdalena Bucior, Rafał Kluz, Andrzej Kubit, Kamil Ochał
Adv. Sci. Technol. Res. J. 2020; 14(1):1–9
DOI: https://doi.org/10.12913/22998624/111662
 

An Optimization Study for Bridge Design of a Porthole Extrusion Die
Önder Ayer, Burcu Gizem Özmen, İsmail Karakaya
Adv. Sci. Technol. Res. J. 2019; 13(4):270–275
DOI: https://doi.org/10.12913/22998624/115109
 

Effect of Nature and Amount of Polypropylene Composite Filler on the Productivity of Extruder with the Cylinder Equipped with Grooves
Volodymyr Krasinskyi, Volodymyr Moravskyi, Oleh Suberlyak, Janusz Sikora, Tomasz Jachowicz
Adv. Sci. Technol. Res. J. 2019; 13(4):264–269
DOI: https://doi.org/10.12913/22998624/114960
 

Assessment of Influence of Sample Averaging on Accuracy of Point Coordinates Measurement Performed Using Laser Tracking Systems
Maciej Gruza, Piotr Gąska, Adam Gąska, Wiktor Harmatys, Michał Jedynak, Konrad Kobiela
Adv. Sci. Technol. Res. J. 2019; 13(4):94–99
DOI: https://doi.org/10.12913/22998624/114186
 

Strength of Joints with “Hi-Lok” Fasteners in Aircraft Safety Considerations
Mariusz Kłonica, Radosław Bielawski
Adv. Sci. Technol. Res. J. 2019; 13(4):87–93
DOI: https://doi.org/10.12913/22998624/114179
 

Thermoforming of a Polystyrene Sheet with a Vibrating Male Mold
Emil Sasimowski, Przemysław Filipek
Adv. Sci. Technol. Res. J. 2019; 13(4):246–254
DOI: https://doi.org/10.12913/22998624/114028
 

Application of Fourier Series for Evaluation of Roundness Profiles in Metrology
Augustín Görög, Ingrid Görögová
Adv. Sci. Technol. Res. J. 2019; 13(4):30–38
DOI: https://doi.org/10.12913/22998624/113620
 

Analysis of the Influence of Support During Measurement Using Coordinate Measuring Techniques
Roman Michalski, Michał Wieczorowski, Przemysław Jerzy Glazowski, Bartosz Gapiński
Adv. Sci. Technol. Res. J. 2019; 13(4):22–29
DOI: https://doi.org/10.12913/22998624/113608
 

Prototyping of an Individualized Multi-Material Wrist Orthosis using Fused Deposition Modelling
Filip Górski, Wiesław Kuczko, Weronika Weiss, Radosław Wichniarek, Magdalena Żukowska
Adv. Sci. Technol. Res. J. 2019; 13(4):39–47
DOI: https://doi.org/10.12913/22998624/113543
 

Recognition Characteristics of Interface Designed for Gesture Operations of 3D Objects
Tsutomu Sekine
Adv. Sci. Technol. Res. J. 2019; 13(4):143–150
DOI: https://doi.org/10.12913/22998624/113475
 

Methodology of Low Cost Rapid Manufacturing of Anatomical Models with Material Imitation of Soft Tissues
Magdalena Żukowska, Filip Górski, Radosław Wichniarek, Wiesław Kuczko
Adv. Sci. Technol. Res. J. 2019; 13(4):120–128
DOI: https://doi.org/10.12913/22998624/113426
 

Proposal of Conversion the Tugboat Engines to Diesel - LNG Operation
Martin Jurkovič, Tomas Kalina, Lubomir Jancosek, Robert Kadnar, Piotr Gorzelanczyk, Karel Jerabek
Adv. Sci. Technol. Res. J. 2019; 13(4):129–142
DOI: https://doi.org/10.12913/22998624/113424
 

Soft-Sensing in Batch Annealing Based on Finite Differential Method and Support Vector Regression
Ján Kačur, Milan Durdán, Marek Laciak, Patrik Flegner
Adv. Sci. Technol. Res. J. 2019; 13(4):70–86
DOI: https://doi.org/10.12913/22998624/112542
 

Creating the Structure and Properties of 7075 Alloy Casts by Thermal and Forming Processes
Krzysztof Majerski, Anna Dziubińska, Grzegorz Winiarski, Michał Szucki, Krzysztof Drozdowski
Adv. Sci. Technol. Res. J. 2019; 13(4):15–21
DOI: https://doi.org/10.12913/22998624/112361
 

Identifying Optimal FSW Process Parameters for 2024 Al Alloy Butt Joints
Rafał Kluz, Magdalena Bucior, Andrzej Kubit
Adv. Sci. Technol. Res. J. 2019; 13(4):48–53
DOI: https://doi.org/10.12913/22998624/110740
 

Effect of Distilled Water and Kerosene as Dielectrics on Machining Rate and Surface Morphology of Al-6061 During Electric Discharge Machining
Rubab Arshad, Shahid Mehmood, Masood Shah, Muhammad Imran, Faisal Qayyum
Adv. Sci. Technol. Res. J. 2019; 13(3):162–169
DOI: https://doi.org/10.12913/22998624/111846
 

Experimental Research of the Weakening of the fFuselage Skin by RFSSW Single Row Joints
Andrzej Kubit, Magdalena Bucior, Rafał Kluz, Wojciech Bochnowski, Ryszard Perłowski
Adv. Sci. Technol. Res. J. 2019; 13(3):90–97
DOI: https://doi.org/10.12913/22998624/110373
 

The Project of a New Controlling System
Erika Fecková Škrabuľáková, Elena Grešová, Jozef Svetlík
Adv. Sci. Technol. Res. J. 2019; 13(3):67–75
DOI: https://doi.org/10.12913/22998624/110105
 

Analysis of Temperatures in the Cold Storage of Finished Products
Gabriela Bogdanovská, Beáta Stehlíková, Ján Kačur
Adv. Sci. Technol. Res. J. 2019; 13(3):54–66
DOI: https://doi.org/10.12913/22998624/109816
 

Influence of the Trochoidal Tool Path on Quality Surface of Groove Walls
Kamil Piotr Waszczuk, Hubert Skowronek, Paweł Karolczak, Maciej Kowalski, Marek Kołodziej
Adv. Sci. Technol. Res. J. 2019; 13(3):38–42
DOI: https://doi.org/10.12913/22998624/109789
 

Surface Quality in Milling of AZ91D Magnesium Alloy
Ireneusz Zagórski, Jarosław Korpysa
Adv. Sci. Technol. Res. J. 2019; 13(2):119–129
DOI: https://doi.org/10.12913/22998624/108547
 

Statistical Analyses of Productivity Model Parameters for Process Improvement
Zahid Hussain
Adv. Sci. Technol. Res. J. 2019; 13(2):157–167
DOI: https://doi.org/10.12913/22998624/106240
 

Examination of Aircraft 's Cable Control Systems Tension
Józef Sebastian Brzęczek
Adv. Sci. Technol. Res. J. 2019; 13(2):65–71
DOI: https://doi.org/10.12913/22998624/106238
 

Evaluation of the Optimum Machining Stability of a Milling Tool with Different Flutes and Overhangs
Yung-Chih Lin, Kung-Da Wu, Wei-Cheng Shih, Jui-Pin Hung
Adv. Sci. Technol. Res. J. 2019; 13(2):56–64
DOI: https://doi.org/10.12913/22998624/106235
 

Approaches to the Evaluation of Thermal-Hygric Microclimatic Conditions in Selected Manufacturing Organizations
Miriam Andrejiova, Ružena Králiková, Miriama Piňosová, Miroslav Rusko
Adv. Sci. Technol. Res. J. 2019; 13(2):14–23
DOI: https://doi.org/10.12913/22998624/105978
 

Simulation Based Measuring the Benefits of Converting to Lean Product Design and Development: A Case Study of Manufacturing Sector of Pakistan
Muhammad Sajid, Ahmad Wasim, Salman Hussain, Mirza Jahanzaib
Adv. Sci. Technol. Res. J. 2019; 13(1):128–137
DOI: https://doi.org/10.12913/22998624/103384
 

Comparative Analysis of Tube Piercing Processes in the Two-Roll and Three-Roll Mills
Zbigniew Pater, Łukasz Wójcik, Patrycja Walczuk
Adv. Sci. Technol. Res. J. 2019; 13(1):37–45
DOI: https://doi.org/10.12913/22998624/102766
 

The Effects of Calcium Carbonate Filler on HDPE Pipe
Samira Kherici, Djillali Benouali, Chekhar Nouredine
Adv. Sci. Technol. Res. J. 2022; 16(3)
 

Design and Implementation of a Dynamic Testing Rig for Testing of Pipe Conveyor Belt and their Components
Peter Michalik, Vieroslav Molnár, Gabriel Fedorko
Adv. Sci. Technol. Res. J. 2022; 16(3)
 

High-Performance Milling Techniques of Thin-Walled Elements
Magdalena Zawada-Michałowska
Adv. Sci. Technol. Res. J. 2022; 16(3):98–110
 

Effect of Machining Settings and Tool Geometry on Surface Quality After Machining of Al/CFRP Sandwich Structures
Elżbieta Doluk, Anna Rudawska
Adv. Sci. Technol. Res. J. 2022; 16(3):22–33
 

Dynamic Analysis of the Starting and Braking of the Table of CNC Machine Tool
Damian Moń, Jerzy Józwik, Magdalena Zawada-Michałowska
Adv. Sci. Technol. Res. J. 2022; 16(3):34–46
 

Case Study of Composite Chassis Manufacturing Process Using Low Temperature Molds Tempered with Gradual Heat Annealing Process
Witold Rządkowski, Przemysław Klik, Jan Tracz, Michał Kowalik
Adv. Sci. Technol. Res. J. 2022; 16(3):12–21
 

Decision-Making Process Development for Industry 4.0 Transformation
Ahmad Sajjad, Wasim Ahmad, Sulman Hussain
Adv. Sci. Technol. Res. J. 2022; 16(3):1–11
 
Most read
Indexes
 
Keywords index
Authors index
© 2006-2022 Journal hosting platform by Bentus