All issues
Volume 13, Issue 3, 2019
Plastic Deformation, Mechanical and Adhesive Properties of Bio-Plastic Material
Adv. Sci. Technol. Res. J. 2019; 13(3):1–15
An Algorithm in the Process of Planning of Safety Pathway – a Collision-Free Pathway of a Robot
Adv. Sci. Technol. Res. J. 2019; 13(3):16–23
Development of Parametric CAD Model and Structural Analysis of the Car Jack
Adv. Sci. Technol. Res. J. 2019; 13(3):24–30
Tensile Forces in Lift Carrier Ropes Exerted by the Fluid Pressure
Adv. Sci. Technol. Res. J. 2019; 13(3):31–37
Influence of the Trochoidal Tool Path on Quality Surface of Groove Walls
Adv. Sci. Technol. Res. J. 2019; 13(3):38–42
Kinematic Modeling and Analysis of a Walking Machine (Robot) Leg Mechanism on a Rough Terrain
Adv. Sci. Technol. Res. J. 2019; 13(3):43–53
Analysis of Temperatures in the Cold Storage of Finished Products
Adv. Sci. Technol. Res. J. 2019; 13(3):54–66
Investigation of Electrical Properties for Cantilever-Based Piezoelectric Energy Harvester
Ahsan Ali, Riffat Asim Pasha, Muhammad Abdullah Sheeraz, Zubair Butt, Hassan Elahi, Afzaal Ahmed Khan
Adv. Sci. Technol. Res. J. 2019; 13(3):76–85
Mobile Devices and Applications Use for Students of Technological Education
Adv. Sci. Technol. Res. J. 2019; 13(3):86–89
Experimental Research of the Weakening of the fFuselage Skin by RFSSW Single Row Joints
Adv. Sci. Technol. Res. J. 2019; 13(3):90–97
A New Method for an Electric Vehicle Wireless Charging System Using LCC
Adv. Sci. Technol. Res. J. 2019; 13(3):98–112
Application of Nanoparticles in the Process of Phase Change Paraffin in a Chamber
Adv. Sci. Technol. Res. J. 2019; 13(3):113–119
Assessment of Tribological Properties of Single- and Double-Layer Pad Coatings Deposited onto Cultivator Points
Adv. Sci. Technol. Res. J. 2019; 13(3):120–128
Effect of Natural Aging and Fatigue Crack Propagation Rate on Welded and Non-Welded Aluminum Alloy (AA2219˗T87)
Mudasir Ijaz, Faisal Qayyum, Hassan Elahi, Mudaser Ullah, Marco Eugeni, Saeed Badshah, Paolo Gaudenzi
Adv. Sci. Technol. Res. J. 2019; 13(3):129–143
Numerical Crush Analysis of Thin-Walled Aluminium Columns with Square Cross-Section and a Partial Foam Filling
Adv. Sci. Technol. Res. J. 2019; 13(3):144–151
A Risk Analysis and Ranking Application for Lifting Vehicles Used in Construction Sites with Integrated AHP and Fine-Kinney Approach
Adv. Sci. Technol. Res. J. 2019; 13(3):152–161
Effect of Distilled Water and Kerosene as Dielectrics on Machining Rate and Surface Morphology of Al-6061 During Electric Discharge Machining
Adv. Sci. Technol. Res. J. 2019; 13(3):162–169
Failure Analysis of Thin-Walled Composite Profile Subjected to Axial Compression
Adv. Sci. Technol. Res. J. 2019; 13(3):170–178
Comparing of Microhardness of the Stellite 6 Cobalt Alloy Implanted with 175 keV Mn+ Ions and 120 keV N+ Ions
Adv. Sci. Technol. Res. J. 2019; 13(3):179–185
Fretting-Wear Mechanism of Textured Surfaces
Mykhaylo Pashechko, Volodymyr Marchuk, Myroslav Kindrachuk, Oleksandr Tisov, Anatolii Kornienko, Oleksandr Dukhota
Adv. Sci. Technol. Res. J. 2019; 13(3):186–191
Vibration Based Gear Fault Diagnosis under Empirical Mode Decomposition and Power Spectrum Density Analysis
Adv. Sci. Technol. Res. J. 2019; 13(3):192–200
Metallographic Comparison of Copper and Brass Plasma Reactor Electrodes After a Month of Operation
Adv. Sci. Technol. Res. J. 2019; 13(3):201–209
Effect of Tool Kinematics on Tube Flanging by Extrusion with a Moving Sleeve
Adv. Sci. Technol. Res. J. 2019; 13(3):210–216
System Identification and Model Predictive Control of the Chatter Phenomenon in Turning Process
Adv. Sci. Technol. Res. J. 2019; 13(3):217–228
Most read