PL EN
 
Articles by Jana Petrů
 

Experimental Investigation of Cutting Forces in High-Feed Milling of Titanium Alloy
Jana Petrů, Lukáš Drábek, Jiří Hajnyš, Dalibor Jurok, Marek Pagáč, Jakub Měsíček
Adv. Sci. Technol. Res. J. 2020; 14(1):89–95
DOI: https://doi.org/10.12913/22998624/113615
 
Stats
Abstract
Article (PDF)
 

A CHOICE OF THE OPTIMUM CUTTING RANGES FOR CUTTING NOZZLES A-SD FOR SELECTION OF METALLURGICAL MATERIAL
Dana Stančeková, Anna Rudawska, Albert Kulla, Jana Petrů, Jozef Holubják
Adv. Sci. Technol. Res. J. 2018; 12(3):106–113
DOI: https://doi.org/10.12913/22998624/92095
 
Stats
Abstract
Article (PDF)
 

SURFACE MICROHARDENING STUDIES ON STEELS AFTER HIGH FEED MILLING
Jana Petrů, Tomáš Zlámal, František Špalek, Robert Čep
Adv. Sci. Technol. Res. J. 2018; 12(2):222–230
DOI: https://doi.org/10.12913/22998624/91888
 
Stats
Abstract
Article (PDF)
 

Effect of the Cutting Tool Geometry on the Tool Wear Resistance when Machining Inconel 625
Tomáš Zlámal, Jiří Hajnyš, Jana Petrů, Ivan Mrkvica
Adv. Sci. Technol. Res. J. 2018; 12(1):236–243
DOI: https://doi.org/10.12913/22998624/86262
 
Stats
Abstract
Article (PDF)
 

Effect of the Cutting Tool Geometry on the Tool Wear Resistance When Machining Inconel 625
Tomáš Zlámal, Jiří Hajnyš, Jana Petrů, Ivan Mrkvica
Adv. Sci. Technol. Res. J. 2017; 11(4):286–293
DOI: https://doi.org/10.12913/22998624/80925
 
Stats
Abstract
Article (PDF)
 

The Properties of Regenerative Polymer Mass
Anna Rudawska, Albert Wierzchowski, Miroslav Müller, Jana Petrů, Nataša Náprstková
Adv. Sci. Technol. Res. J. 2017; 11(3):130–138
DOI: https://doi.org/10.12913/22998624/71149
 
Stats
Abstract
Article (PDF)
 

EFFECT OF CHIP BREAKERS ON THE CUTTING FORCE DURING THE MACHINING OF STEEL C45
Jiří Kratochvíl, Jana Petrů, Marek Pagáč, Jozef Holubják, Jozef Mrazik
Adv. Sci. Technol. Res. J. 2017; 11(1):173–178
DOI: https://doi.org/10.12913/22998624/66506
 
Stats
Abstract
Article (PDF)
 

IMPACT OF CUTTING TOOL GEOMETRY ON THE DYNAMIC LOAD OF SYSTEM IN THE MACHINING PROCESS OF NICKEL ALLOY 625
Jiří Hajnyš, Tomáš Zlámal, Jana Petrů, Marek Pagáč, Anna Rudawska
Adv. Sci. Technol. Res. J. 2016; 10(32):24–31
DOI: https://doi.org/10.12913/22998624/65111
 
Stats
Abstract
Article (PDF)
 

MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING OF SPECIAL ALLOYS
Tomáš Zlámal, Jana Petrů, Ondřej Vortel, Marek Pagáč, Pavel Krajkovič
Adv. Sci. Technol. Res. J. 2016; 10(31):144–150
DOI: https://doi.org/10.12913/22998624/64074
 
Stats
Abstract
Article (PDF)
 
Most read
Indexes
 
Keywords index
Authors index
Copyright © 2006-2020 Bentus All rights reserved.